Sheldon Brown photo

Sheldon Brown's
Bicycle Glossary G


find us on FB

Opinions and value judgments are our own, unless otherwise noted
-- Sheldon (d. 2008), Harriet, John.
Additions and corrections are most welcome.

A - B - C - D - EF - G - H - IJKL - M - NO - PQ - R - S - T - UVWXYZ

Up to previous page

Spoke Divider

Gage
Alternate spelling of gauge.
Gain ratio
One of the three comprehensive systems for numbering the gear values for bicycle gears. It is the only system that takes crank length into account, giving a true value for the relative leverage of different gears on bicycles with different size wheels and cranks. Gain ratio has the further advantage of not needing any units. It is a pure ratio, and is the same whether you use metric or inch-based units to calculate it. See also gear inch and development.

For more detail on gain ratios, see my article on the subject.

You can calculate gain ratios., gear inches or meters development. with my Online Gear Calculator or with your slide rule

Gas Pipe
A derisive term for the "high tensile" tubing used to build cheap bicycles. Since low-end bicycles are made of low-quality steel, the builders compensate by using heavy, thick-walled tubes.
Gauge

Spoke Divider

Spoke Divider

Gear
The "gear" of a bicycle relates to the mechanical advantage of the whole drive system. In a low gear, the pedals are easy to turn, but you have to spin very fast to get any speed up. In a high gear, the pedals are hard to turn, but you don't have to make them turn very fast to make the bicycle go fast.

The gear of a bicycle depends on the ratio between the sizes of the front and rear sprockets, and the size of the drive wheel. If the bicycle is equipped with planetary gears, they also affect the gear. There are several ways of designating gears numerically. See gain ratios, gear inches, and development.

For information on using your bicycle's gears, see my article: Everything You Wanted to Know About Shifting Your Bicycle's Gears, But Were Afraid to Ask

Gear Inches
One of the three comprehensive systems for numbering the gear values for bicycle gears. It is the equivalent diameter of the drive wheel on a high-wheel bicycle. When chain-drive "safety" bikes came in, the same system was used, multiplying the drive wheel diameter by the sprocket ratio. It is very easy to calculate: the diameter of the drive wheel, times the size of the front sprocket divided by the size of the rear sprocket. This gives a convenient two- or three-digit number. The lowest gear on most mountain bikes is around 22-26 inches. The highest gear on road racing bikes is usually around 108-110 inches. Unfortunately, the handwriting is on the wall for all inch-based measurement systems.

See also gain ratios and development.

You can calculate gear inches, gain ratios, or meters development. with my Online Gear Calculator or with your slide rule

Gear CaseChain case
A chainguard that totally encloses the chain, usually found only on roadsters. Gear cases (also known as "chain cases") are extremely practical for utility bicycles. They keep the chain clean in all weather, and permit cycling in ordinary street clothes without risk of soiling. Unfortunately, a satisfactory chain case to work with derailer gears has not been developed, so they are only found on one-speed bikes or those with internal-gear hubs. Sometimes referred to as an "oil bath", though most of them are not tight enough to act as an actual "oil bath." An exception is older Sunbeam models, where there was actually a pool of oil contained in the bottom of the gear case.

Chain replacement with a gear case:

(To actually remove the chain case, you need to remove the right crank. There's a bolt hidden behind the chainwheel, screwed into a special fitting on the chainstay.)

Spoke Divider

Spoke Divider

Gel
A type of closed-cell foam, in which the bubbles are under higher-than-normal pressure. Originally developed by Spenco for wheelchair cushions, gel is also popular for saddles and saddle covers, and for padding the palms of cycling gloves.

Gel has been rather over hyped as a cure-all for saddle related discomfort.

Generator
A generator (or "dynamo ") is a device for turning mechanical energy into electricity. Generator-powered bicycle lights have been available for many decades. Generators have the advantage of being ready to use at any time and costing nothing to operate.

Unfortunately, the output of a generator depends on the bicycle's speed. Generator lights go dark when the bicycle is stopped, and are dim at low speeds. Fast riding can cause the voltage to rise to the point that bulbs burn out prematurely.

The efficiency of LEDs has made generator lights more practical. Some generator systems now charge a small \battery or capacitor and keep the light shining when the bicycle is stopped.

The widespread availability of rechargeable batteries has considerably reduced the desirability of generator powered systems. The vast majority of bicycle generator systems only put out 3 watts; a very few put out 6 watts (when running at optimal speed.) Since rechargeable systems commonly put out 15 watts or more, at all speeds, they are generally preferable for most applications.

Ghost Shifting
Refers to when a bike shifts gears spontaneously. See my separate article on Autoshifting
Gizzmo ®
See: Erickson Gizzmo ®
Gloves
Gloves are a good idea for cycling, even in warm weather. They considerably reduce hand discomfort on longer rides, partly due to their padding, and partly because they aren't as slippery on the handlebars, reducing the need to grip the handlebars so tightly and reducing hand fatigue. They also allow use of a hand to break a fall without injury.

Traditional cycling gloves are fingerless, with leather palms, often double layered with a foam sandwich under the heel of the hand. The backs were traditionally a crocheted mesh, though Lycra ® is more common of late.

goat head seeds
Goat head

The seed of a low-growing flowering plant common in warm climates. Each seed has thorns which can puncture bicycle tires, like a thumbtack.

More detail at Wikipedia

 

Spoke Divider

Spoke Divider

Goofy Footed
When you coast with the cranks horizontal, ideally you should have the left foot forward, right foot rear. This way, the stresses on the crank/bottom bracket interface are in the usual direction.

If you coast with your right foot forward, that's sometimes called "goofy footed" and can contribute to loosening up or damaging the crank, since it applies stress in the opposite direction than the stresses of normal pedaling.

This term comes from the world of surfing, where left-foot forward is the norm.

Goose Neck
Handlebar stem, particularly a stem with a long forward extension.
Granny Gear
Slang term for the smallest chainwheel on a triple crank set.

Note that this term is not a general term for the lowest gear of a bicycle, but specifically refers to just the smallest chainwheel on a crankset with more than two chainwheels.

Grease
A lubricant in the form of a viscous paste, rather than a liquid oil. Grease is generally a more difficult to apply, because most bicycle parts cannot be greased effectively without disassembly. Grease lubrication is commonly used on all ball bearings. Good mechanics also use grease (or oil) on the threads of most threaded fittings and fasteners, and also inside the steerer (to keep the stem from becoming stuck) and the seat tube (to keep the seatpost from becoming stuck.)

There are a great many different greases on the market with different special features, mainly for automotive applications. For bicycle use, almost any grease is adequate, since the loads and temperatures are generally low. In wet conditions, a water-resistant grease is preferable. Coaster brakes need a heat-resistant grease.

Greaseguard ®
A Sun Tour system with fittings to allow grease to be injected into bearings without the need to disassemble them; especially intended for mountain-bike use, in which a bicycle may be partly submerged in water.
GripShift ®
SRAM trademark for twist-grip shifters.
Group
A group is a set of parts for one bicycle from (usually) a single manufacturer. The practice of selling parts as a group (or "gruppo" in Italian) probably originated with Campagnolo in the 1960's.

A group would normally include (as a minimum) the following:

If a particular manufacturer doesn't make one or more of these items, it may have some made under its name by another manufacturer to fill in a group. For instance, when Mavic was offering groups, it had everything listed above except for brakes, so it had brakes made under its name by Modolo and Dia Compe, and pedals by Look.

If the manufacture offers them, a group could also include:

Note the distinction between a "group" and a "kit": In addition to the group, a kit includes everything needed to turn a frame into a bicycle: built-up wheels (rims, spokes, tires, rim tape, tubes), handlebars, saddle, etc.

Spoke Divider

Spoke Divider

Grouppo
Common misspelling of "Gruppo."
Groupset, Group Set
Redundant term for "group." More common in British usage than American.
Gruppo
Italian for "group." The use of the term "gruppo" is sometimes considered an elitist affectation, especially when referring to parts which are not of Italian manufacture.
Gum
Tan, semi-translucent rubber, commonly natural rubber. This was once commonly use on the sidewalls of tires and on brake hoods. Natural gum rubber lacks the additives which would help defend it against ozone and other chemicals. Gum rubber tends to crack and deteriorate into a sticky mass over time. Some tan rubber is not natural gum rubber, and is more immune to this deterioration. See skinwall, blackwall, gum hoods.
Gusset
A reinforcement welded or brazed to one or more tubes of a frame to reinforce an area of high stress.
Gyro ®
A particular type of rotor, from Odyssey ®. The Gyro features a split cable, so that the rotor is pulled evenly from both sides. This avoids any mechanical friction from the rotor, since it does not slide along the stem shaft as with other rotors. In fact, the rotor part of the system touches nothing but the cables.

In addition, the Gyro has a ball-bearing built into it, so it has very little friction while turning.

Gyro adjustment:

Every part in a brake system has a certain amount of "travel" available. For instance, the lever can go from its rest position (which is often adjustable for hand size by a small screw) as you squeeze it to the point where the lever bumps into the handlebar grip.

The caliper has a limited amount of travel too, limited by the brake shoes hitting the rim on the inward side, and by whatever stops the arms from springing out when the brake is released.

On any braking system, the outward (rest position) travel should be limited by the lever's bumping against its stop, but the inward travel should be limited only by the brake shoes' hitting the rim. You should be able to squeeze the lever as hard as you can without having the lever bump into the grip, because once the lever bottoms out, no more braking power is transmitted to the brake shoes, no matter how much harder you squeeze.

The Gyro has a limited amount of travel available to it also, and it is important to ensure that the Gyro itself is not the limiting factor in either inward or outward travel.

Start by hooking up the upper cable between the lever and the Gyro. Operate the lever with one hand while pulling downward on the Gyro assembly. The adjusting barrels on the Gyro (and on the lever, if there is one) should be set so that the lever just barely stops the Gyro from bottoming out against the headset when you release the lever.

Make sure that the adjusting barrels on both sides are set the same way, so that the Gyro is horizontal. Otherwise, the braking action may vary as you turn the handlebars.

Once the upper cable is set, connect the lower cable to the brake in the usual manner.

Spoke Divider

Down to next page

A - B - C - D - EF - G - H - IJKL - M - NO - PQ - R - S - T - UVWXYZ

Spoke Divider

Spoke Divider

Articles by Sheldon Brown and Others

Copyright © 1996, 2008 Sheldon Brown

Harris Cyclery Home Page

If you would like to make a link or bookmark to this page, the URL is:
https://www.sheldonbrown.com/gloss_g.html

Last Updated: by Harriet Fell